Defender CSD Pure

Benefits

• Deep Consolidation: Reinforces friable and decayed substrates by bonding internal stone particles for improved structural stability.
• Substrate Strengthening: Increases load-bearing capacity and resistance to erosion, cracking, and decay.
• Limestone-Specific Performance: Delivers reliable protection and strengthening where many sealers fail, especially on soft, porous limestone.
• Ultra-Deep Penetration: Penetrates 10–20mm into porous surfaces for long-lasting internal protection.
• UV & Weather Resistant: Stable under sunlight and outdoor exposure.
• Vapour Permeable: Maintains breathability to prevent trapped moisture and internal damage.
• Natural Finish: Leaves no visible film, preserving the original look and colour of the substrate.
• Long-Term Protection: Effective for up to 15 years; reapplication every 8–12 years is recommended in high-wear environments.

Application areas and surface suitability

Defender CSD Pure is a consolidator and strengthener for stone.

Formulated to provide premium protection to porous construction materials and is ideally suited to the protection of heritage and delicate/friable/crumbling stone. Defender CSD Pure is ideal for limestone, sandstone and concrete structures.

Expected Wear:
Defender CSD Pure will provide premium protection for up to 15 years and in many applications, several years longer. However application methods, weather conditions, traffic, harsh cleaning methods and substrate type will affect wear. Avoid use of solvents, strong acids and strong alkalis for extended sealer life.
It is recommended that the sealer be re-applied every 8 – 12 years where harsh conditions exist.

Considerations:
Not to be used as a sub-terrain waterproofing. Should not be applied if temperature is above 40 degrees or if rain is expected within 2 hours of application. If rain has preceded the application, the surface should be allowed 24 hours to dry completely.

How to use

Read and understand the SDS before use
Always pre-test in an inconspicuous location for sensitivity to chemicals.

Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 10 m2 / Lt per coat for open structure, highly porous substrates. And 10 to 20 m2 / Lt per coat for dense, less porous substrates.

Note:
Application on large concrete areas should be based on a preset coverage rate using a dedicated sprayer or painting equipment. No subsequent removal of excess product is required.

Adhesive Compatibility:
When a tile is dip sealed prior to being installed, it will become slightly water repellent. This means that a standard water based adhesive may not adhere to the surface. A suitable polymer modified grout should be used, which is designed to overcome the repellency of a penetrating sealer.
Compatible adhesives include:
1. Davco SE-7 (with Davelastic)
2. Mapie Granirapid

Surface Preparation:

• New installations must be fully cured before application of Defender CSD Pure (Min 48 hours, however some concrete installations may take up to 7 days to cure. Confirm with the structural engineer).
• Existing stone and grout must be totally clean, dry and chemical free.
• Coverage can vary dramatically depending on the degree of porosity, but is normally 5 to 15 m2 / Lt per coat for open structure, highly porous substrates and 15 to 25 m2 / Lt per coat for dense, less porous substrates.
• Do not apply in direct sunlight. Temperature must be between 10°C and 28°C.
• Highly absorbent surfaces may require two coats.

Dilutions

Ready to use

Application

1. Apply 1 to 2 coats of Defender CSD Pure by generously saturating the surface using a polish applicator, roller or sprayer to an area which can be easily reached. (Approximately 15m2).
2. Ensure even coverage. When treating vertical surfaces, start application from the bottom, moving upwards to avoid uneven coverage.
3. The surface must be shiny wet with a liquid film for at least 30 seconds. For very porous substrates more sealer may need to be applied.
4. Allow 5 – 10 minutes for the sealer to absorb into the surface. On horizontal surfaces move the excess product with a squeegee to a new section.
5. If a second coat is to be applied, wait 20 to 30 minutes and repeat the process.
6. Using absorbent towelling or applicator, wipe off any sealer remaining on the surface after 10 minutes of the last application. Moisten the towel with Methylated Spirits to remove residues which have dried on the surface.
7. Allow 6 – 12 hours before returning area to traffic. Keep dry for 24 hours. Achieves a full cure in 24-48 hours.

Test results & approvals

• Test report: Resistance to salt attack AS/NZS 4456.10-2003